Featuring an anti-splash cover and sleek, streamlined casing, the Leaf Eater Slimline is our most aesthetically-sensitive rain head. But don’t be fooled by its attractive appearance. It still effectively filters your water at high flow rates so you don’t compromise on performance.
Rather than shedding leaves and debris onto your deck or other areas, the Leaf Eater Slimline collects them inside its anti-splash cover. When the rain head requires emptying, a red overflow flag automatically appears. Simply empty it and reset – too easy.
With its mosquito-proof 955 micron stainless steel screen, the Leaf Eater Slimline stops leaves, debris, mosquitoes and other pests from getting into your downpipes and rain harvesting system. This gives you better quality water and more of it – all with a great-looking rain head.
Rain Heads filter leaves and debris out of your downpipes with their 955 micron screens. They also minimise splashing to increase the volume of rainwater you harvest.
Rain Heads secure the system with the 955 micron mosquito-proof screens that prevent insects and other animals from entering and breeding or living in your downpipes.
For best performance, check and empty your Leaf Eater Slimline rain head on a regular basis to remove captured leaves and debris. When the red overflow indicator is visible, this is a warning signal to let you know that leaf and debris removal is required.
Remove the filter by pulling it out from the rear body. This may require a little force as the rubber gasket creates a tight seal. Empty the filter body, removing any captured leaves and debris. Then hose or brush out the filter body to remove finer debris.
The frequency at which maintenance is required will depend on the environment in which your Leaf Eater Slimline rain head is installed. For example, if you install your Leaf Eater Slimline in a high leaf area, maintenance will be required more regularly.
Rain heads must be installed so they are higher than the inlet on your rainwater tank. This is necessary to allow water to flow through the pipework to your tank and to avoid water overflowing from your rain head.
If you have a wet rain harvesting system (a system where pipes feeding your tank sit below the level of the tank inlet and hold water), you should install your rain head a minimum of 500mm (19.6″) above the height of your tank inlet. Where possible, we recommend that you maximise the height of your rain head in relation to your tank inlet even further. This may be especially necessary if you have a longer wet system.
For best results, consult a licenced plumber to discuss the optimal height of your rain heads so you can avoid damage to your property, risks to your personal safety and other negative consequences of water overflowing from your rain heads.
The ideal location for a rain head is directly beneath your gutter outlet at the fascia board or eaves. Where access is difficult – for example, on a two-storey house – your rain head can be installed “mid” mount on the wall lower down away from the gutter. When selecting your installation point, it’s important to consider the height of your rainwater tank inlet, as your rain head should be installed a minimum of 500mm (19.6″) above the height of your tank inlet. Your chosen installation point should tread the balance between maximum height in relation to the height of your tank inlet, and safe and easy accessibility for maintenance.
Yes. All the rain heads in our Leaf Eater range can be painted to match your home or building. Check with your local paint retailer to ensure you select a product that’s suitable for use with plastic.
All our Leaf Eater rain heads are suitable for use in areas with pine needles. However, due to the fine size of the needles, more regular maintenance will be required to remove any pine needle debris from your rain head.
The most common reason a rain head overflows is insufficient or irregular maintenance. Check and clean your rain head screens regularly to ensure they continue to function optimally.
Alternatively, your rain head may overflow if there is insufficient “fall” from the rain head to the tank inlet – in other words, if your rain head is not positioned high enough in relation to the height of your rainwater tank inlet. A height difference between your rain head and tank inlet is necessary to allow water to be pushed through your rain harvesting system under gravity.
Rain heads with an open “face” have an angled, self-cleaning screen designed to minimise splashing as leaves and debris are deflected away from the flow of water. This applies to all our rain heads that feature our Clean Shield screens, as well as the Leaf Eater Original.
If you are still concerned about splashing, consider choosing a rain head with an anti-splash cover such as the Leaf Eater Slimline or Leaf Eater Ultra.
All our Leaf Eater rain heads feature mosquito-proof screens and are designed to keep leaves, debris, mosquitoes and other pests out of your downpipes and rain harvesting system. Several of our rain heads feature patented VH pivots for installation on horizontal and vertical downpipes, some feature anti-splash covers and some feature additional technology such as our Hydro Activated Filtration screen system and red overflow indicator flags.