Leaf Eater Advanced with The Hood | Rain Harvesting by Blue Mountain Co
New
90mm

Leaf Eater Advanced with The Hood

Rain Heads
This is the Leaf Eater Advanced with The Hood. This rain head reduces contamination and captures more rainwater with its custom designed Hood cover and screen.
Size 90mm RHAD10
Wet Leaves

Improve your rainwater quality

The Leaf Eater® Advanced with The Hood keeps leaves and debris out of your pipes and tank to prevent clogging, blockages, anaerobic fermentation and tannin leaching.

Calm Water

Capture and store more rainwater

The Hood is a great way to ensure your rain heads are capturing the most water from your downpipes. An added benefit of The Hood is that it also minimizes splashing that might occur on a leaf-shedding rain head. This can be particularly useful if your rain heads are located above walkways, patios, or other high traffic areas.

Rhad10 Exploded

Maintain with ease

Maintaining your rain head is as simple as lifting the Hood cover up your inlet pipe, then brushing or washing the debris away from the screen.

How it works

Rain Harvesting’s Patented VH Pivot

VH Pivot Line Drawing

This Rain Head incorporates a VH Pivot outlet that swivels to suit vertical or horizontal downpipes. Pivot the outlet to suit vertical or horizontal (rear outlet) downpipes enabling a variety of installation options in one product, for instance under in a tight space under a low set fascia.

Rain Heads filter leaves and debris out of your downpipes with their 955 micron screens. They also minimise splashing to increase the volume of rainwater you harvest.

Rain Heads secure the system with the 955 micron mosquito-proof screens that prevent insects and other animals from entering and breeding or living in your downpipes.

Learn more about the 4 pillars of designing a Rain Harvesting system. 

  • Specifications

  • What's in the box?
    • Leaf Eater Advanced Rain Head
    • The Hood Cover
    • The Hood Screen
  • Tools you might need
    • Tape measure
    • Marker pen
    • Saw
    • Screws
    • Screwdriver or drill
    • Solvent cement glue
  • Installation

    Gutter, eave & “mid” mount (Vertical)

    1. Locate the position at which you will be installing your Leaf Eater Advanced with The Hood rain head. Whether this is directly under your gutter/eave or midway down your downpipe, it should be a minimum of 500mm above your tank inlet and tank overflow pipe.

    2. For installation on a vertical downpipe directly under your gutter, measure 200mm from the bottom of the existing gutter pop and remove this section of downpipe. For installation under your eaves or midway down your downpipe, remove a 200mm section of pipe at your desired installation point. Ensure all cut edges are clean and smooth (FIGURE 1).

    3. Remove The Hood screen. (FIGURE 2).

    4. Insert your Leaf Eater Advanced rain head by sliding it up behind the top section of downpipe and then down into position. The rain head outlet pipe should be slid firmly into the bottom downpipe until it can be pushed no further (FIGURE 3).

    5. Using the screw slots provided, screw your Leaf Eater Advanced rain head into position. Ensure appropriate screws (and anchors if required) are used (FIGURE 5).

    6. Reinsert the screen into your rain head. Ensure the screen sits firmly in place and check installation is secure (FIGURE 6).

    7. Slide The Hood cover up the top section of pipe and lower the bottom skirt into the corresponding channel on the screen. If your inlet pipe is 100mm or 4”, you will need to cut away the multi fit inlet so your inlet pipe can fit inside.

    8. If desired, you can paint your rain head to match your downpipes and/or building.

    Gutter Mount (Horizontal)

    1. Locate the position at which you will be installing your Leaf Eater Advanced rain head. Whether this is directly under your gutter/eave or midway down your downpipe, it should be a minimum of 500mm above your tank inlet and tank overflow pipe.

    2. Remove The Hood screen by lifting it up and then out (FIGURE 2).

    3. Swivel the outlet to the horizontal position. Some force may be required.

    4. Position your Leaf Eater Advanced rain head next to your existing pipework and use it as a template to mark top and bottom cutting lines. Cut the pipe where you have marked. Ensure all cut edges are clean and smooth (FIGURE 4).

    5. Use solvent cement to glue the rear outlet into the horizontal pipe. The back fixing plate should sit behind the top section of downpipe.

    6. Screw your Leaf Eater Advanced rain head into position using the screw slots provided. Use appropriate screws (and anchors if required) (FIGURE 5).

    7. Reinsert the screen into your rain head. Ensure the screen sits firmly in place and check installation is secure (FIGURE 6).

    8. Slide The Hood cover up the top section of pipe and lower the bottom skirt into the corresponding channel on the screen. If your inlet pipe is 100mm or 4”, you will need to cut away the multi fit inlet so your inlet pipe can fit inside.

    9. If desired, you can paint your rain head to match your downpipes and/or building.

  • Maintenance
    1. Slide The Hood cover up your inlet pipe and remove The Hood screen.

    2. With the screen removed, either brush off or wash the debris from the screen.

    3. Reinsert the screen to the Leaf eater Advanced body, making sure the screen is fully seated all the way around and flush with the body.

    4. Reinstall the cover, making sure that the skirt around the edge is fully seated in the corresponding channel on the screen.

  • Product FAQs

    How high should I install my Leaf Eater rain head?

    Rain heads must be installed so they are higher than the inlet on your rainwater tank. This is necessary to allow water to flow through the pipework to your tank and to avoid water overflowing from your rain head.

    If you have a wet rain harvesting system (a system where pipes feeding your tank sit below the level of the tank inlet and hold water), you should install your rain head a minimum of 500mm (19.6″) above the height of your tank inlet. Where possible, we recommend that you maximise the height of your rain head in relation to your tank inlet even further. This may be especially necessary if you have a longer wet system.

    For best results, consult a licensed plumber to discuss the optimal height of your rain heads so you can avoid damage to your property, risks to your personal safety and other negative consequences of water overflowing from your rain heads.


    Should I mount my Leaf Eater rain head at the gutter or on the wall?

    The ideal location for a rain head is directly beneath your gutter outlet at the fascia board or eaves. Where access is difficult – for example, on a two-storey house – your rain head can be installed “mid” mount on the wall lower down away from the gutter. When selecting your installation point, it’s important to consider the height of your rainwater tank inlet, as your rain head should be installed a minimum of 500mm (19.6″) above the height of your tank inlet. Your chosen installation point should tread the balance between maximum height in relation to the height of your tank inlet, and safe and easy accessibility for maintenance.


    Can I paint my Leaf Eater rain head?

    Yes. All the rain heads in our Leaf Eater range can be painted to match your home or building. Check with your local paint retailer to ensure you select a product that’s suitable for use with plastic.


    I have pine needles. Which Leaf Eater rain head should I use?

    All our Leaf Eater rain heads are suitable for use in areas with pine needles. However, due to the fine size of the needles, more regular maintenance will be required to remove any pine needle debris from your rain head.


    My Leaf Eater rain head is overflowing. Why is this happening?

    The most common reason a rain head overflows is insufficient or irregular maintenance. Check and clean your rain head screens regularly to ensure they continue to function optimally.

    Alternatively, your rain head may overflow if there is insufficient “fall” from the rain head to the tank inlet – in other words, if your rain head is not positioned high enough in relation to the height of your rainwater tank inlet. A height difference between your rain head and tank inlet is necessary to allow water to be pushed through your rain harvesting system under gravity.


    Will my Leaf Eater rain head splash water into my covered patio area?

    Rain heads with an open “face” have an angled, self-cleaning screen designed to minimise splashing as leaves and debris are deflected away from the flow of water. This applies to all our rain heads that feature our Clean Shield screens, as well as the Leaf Eater Original.

    If you are still concerned about splashing, consider choosing a rain head with an anti-splash cover such as the Leaf Eater Slimline or Leaf Eater Ultra.


    What’s the difference between each rain head in the Leaf Eater range?

    All our Leaf Eater rain heads feature mosquito-proof screens and are designed to keep leaves, debris, mosquitoes and other pests out of your downpipes and rain harvesting system. Several of our rain heads feature patented VH pivots for installation on horizontal and vertical downpipes, some feature anti-splash covers and some feature additional technology such as our Hydro Activated Filtration screen system and red overflow indicator flags.

Products you may be interested in

Maelstrom Filter
Maelstrom Filter
100mm
New
Kit
First Flush Advanced
First Flush Advanced
100mm
Mozzie Stoppa Easy-Clean
Mozzie Stoppa Easy-Clean
90mm
Close

Your selection

Add Rain Harvesting or Plumbing products to your list.