The Clean Rain Ultra keeps leaves and pests out of your downpipes so you can harvest better quality water. Leaf Slide “fingers” deflect larger leaves, while the patented, 955 micron Hydro Active Filtration™ screen keeps mosquitoes out and vibrates for maximum leaf shedding.
With its inbuilt, compact inline first flush diverter and Smart Sense® technology, the Clean Rain Ultra diverts the dirtiest, most contaminant-laden rainwater from your roof into stormwater so it doesn’t threaten the quality of the water in your tank.
With the Clean Rain Ultra, achieving a stylish, integrated look couldn’t be easier. The Clean Rain Ultra’s rain head features a sleek cover and cap, the inbuilt first flush diverter doesn’t require an additional diversion chamber pipe, and the body swivels for convenient positioning.
Clean Rains filter leaves and debris out of your downpipes with their 955 micron screens. They also minimise splashing to increase the volume of rainwater you harvest.
Clean Rains secure the system with the 955 micron mosquito-proof screens that prevent insects and other animals from entering and breeding or living in your downpipes.
Clean Rains help divert the first flush, through their design. They are installed using a T junction or high flow inlet to which the diversion chamber is fitted. As the chamber fills with the initial dirty water from your roof, the hygroscopic washers swell until they seal the inlet, allowing the rest of your rainwater, which is much cleaner, to flow directly to your tank.
The Clean Rain® is mostly self-cleaning, however it may require occasional maintenance in order to keep it functioning optimally.
RAIN HEAD – The leaf slide and vibrating screen can both be removed when the cap and cover are off by lifting up and out. If cleaning is required simply hose or brush off any debris. Replace as per figure 1 and 2.
OUTLET – The outlet has an internal mosquito barrier that prevents any mosquitoes from entering the system. To clean simply remove the outlet by holding the unit in one hand and with a firm pull remove the outlet adaptor.
FIRST FLUSH – The Smart Sense® valve may require the occasional clean to remove any buildup of sediment. To clean remove the Clean Rain® from the wall and take the bottom adaptor off the unit. The hygroscopic washers within the Clean Rain have a long service life and should not require replacement. However, should you notice decreased amounts of first flush or increasingly longer re-set periods then your washers may require replacement. Please contact Rain Harvesting for a full replacement set.
Smart Sense technology utilises a series of hygroscopic washers. When exposed to water, these washers slowly expand, in turn activating the valve by pushing it upwards into the seat. Water is then diverted to the outlet.
Approximately 18-30 litres or 5-8 gallons will be diverted, depending upon a variety of factors. The main factors are flow rate and the period of time since the last downfall. However, several other factors such as rainfall intensity, ambient temperature, humidity and wind will all affect the exact diversion volume.
We do not recommend adjusting the diversion volume. The hygroscopic washers divert an appropriate volume of first flush.
If the unit is new, this will most likely occur because the washers require several rainfalls to properly “bed in”. For the first few rainfalls, the washers will divert a greater volume of first flush water than normal. After several rainfall events the washers will be properly bedded and deliver consistent diversion volumes.
The resetting process is dependent upon a number of environmental factors. Ambient temperature, humidity, wind and location are all major factors in determining the resetting period. Under dry conditions with a moderate temperature, wind and humidity, the Clean Rain should completely reset within 24 to 72 hours.
There are a few quick steps to take to get your Clean Rain diverting again:
Open up your Clean Rain
Feel the hygroscopic washers to see if the they are dry
Note: If they are not dry, they are expanded and working correctly
Look around and check for standing water nearby
If the washers are dry, check there is no debris which bonding the seal to the body – if it is bound together, gently pull the metal rod down to release it.
If there is no debris there, and no obvious obstructions, take a photo and give us a call.
If your clean rain unit has been turned off it will not be able to be turned back on again until the hygroscopic washers are dry and the system has reset. Frost, snow, mist and dew can all activate the hygroscopic washers, so a few days where none of these are present will be required before attempting to turn the unit back on. If this is not possible then removing the unit and storing it in a dry environment for 1-2 days should suffice for the unit to be switched on again. For replacement hygroscopic washers or further information please contact Blue Mountain Co ([email protected]).
Your Clean Rain has been manufactured using materials that are capable of withstanding freezing conditions. If freezing conditions are expected, we recommend turning your unit off via the switch and, if you have a Clean Rain Ultra, ensuring that the cover is in place.
The clean rain system has been optimised for 90mm/3″ pipe. Although the system will accommodate 100mm/4″ pipe it will not be able to deliver 100% diversion should a full-bore flow event happen. We are currently working on developing a system capable of handling a full-bore 100mm/4″ pipe flow.
The easiest way to alter the resetting period is with the breather holes located in the section underneath the outlet (long horizontal indentations with small holes). To shorten the reset period, align the breather holes with any prevailing wind. To prolong the reset, simply turn the breather holes 90 degrees to the prevailing wind.
An alternative way to shorten the reset period is to remove the foam shroud surrounding the washers. It should be noted that by removing the foam shroud the diversion volume will also be decreased.
Your clean rain unit may require a diverter/flow efficiency cap. We have found that some products in the market do not have this piece. If you’re missing a diverter/flow efficiency cap, we can send this to you and provide instructions on fitting it. Look through the top of your Clean Rain to check if this cap is present. It’s a blue, disc-shaped part.